OLRC Race Rules

OLRC Race Rules - 

Box Stock

Motor: Kyosho MZ9P and MZ9E Motor from RTR, allow change the motor wire and remove the safety switch.

Chassis: Kyohso MR03S, MR03S2, MR03 RWD and MR04 RTR

Wheels: Kyosho or PN plastic wheels, Front 8.5mm x 20mm, Rear 11mmx20mm, offset must fit inside of the body.

Tire: Kyosho or PN Mini-Z 8.5mm and 11mm rubber tire only. Homemade tires, Foam tires, Silicon tires, Urethane tires, Ethyl Carbamate tires NOT allowed. No tire insert use. Traction compounds NOT allowed on tire or on race surface. Tire installed to wheel maximum diameter 25.5mm. Tire warmers are allowed. Tires may be cleaned with a 70% alcohol solution. If a driver uses tire cleaner that has been deemed illegal, the driver will be subject to any penalties that apply. Please address any questions concerning tire cleaners at the drivers meeting.

Electronic & Transmitter: Kyohso original from RTR, NO any modification. Gyro and Receiver build in Gyro is not allowed.

Gear Ratio: Fixed 9T Pinion with Stock Gear Diff. Pinion - Kyosho or PN 400329 MR2709 only.

Wheelbase: 90mm to 102mm

Body: Kyosho original AutoScale body, white body, Jomurema GT01 body and TRP Scale body, PN Racing Concept C9 ABS Body, all parts must be original from that body, limited wheel clearance modification allowed. Lexan Window and Lexan Roof allowed. Minimum weight limit 24g.

Batteries: Kyosho Speed House 800HV, Peak Racing 900HV, TRP747, TRP900, PN HP750, PN HP900 and Silver Horse 800, AAA NiMH 4pcs only.

Option Parts: Kyosho or PN Ball Bearing, Front Spring, wheel nut and T-Plate only. Modifications: It must be run in stock configuration.

2wd Stock

Chassis: Kyosho Mini-Z Racer MR01, MR015, MR02, MR03, MR04, MRC MR01 and PNR2.5W. 90mm-98mm wheel base only.

Body: Kyosho Mini-Z, TRP Scale and Jomurema GT01, GL 488 Lambo, Silver Horse R8 body and PN Racing Concept C9 ABS Body only. LeMans body NOT allowed, full windshield and window must be installed, except for clearance, Lexan Window and Lexan Roof with original shape design allowed.

Minimum weight limit 24g.

Motor: Handout motor PN Brushless Sensorless V4 3500kv #164435, all motor comes with standard 14.5 rotor,

Fixed Gear ratio 64 Pitch 16 Pinion (#416416WC Blue, #426416WC Blue, #MR2716WC Blue) / 53T Spur Gear (#MR2953WC Yellow, #MR2055-T53WC Yellow, #RX2853WC Yellow, MWX Slipper Diff 53T Yellow, Xbility One 53T Yellow ONLY.

ESC: Kyosho ASF VE VE Pro MR03S RWD, MR04 RTR ESC, EVO and PN 16A ESC (#500807 and #500807A). Gyro and Receiver build in Gyro is not allowed.

Battery: Cars must be powered by four AAA batteries. Alkaline, Ni-MH or Ni-Cd batteries may be used. No other type of battery may be used. For example: Lithium Polymer may not be used. Additional battery for transponder allowed.

Option Parts: Any aftermarket brand Mini-Z production parts allowed, any homemade parts, 3D print option parts and prototype parts not allowed. Allowed 3D Print Transponder Holder, Body Side Clips, ESC Top Cover and front bumper allowed.

Wheel: All brand Plastic and Aluminum Mini-Z production wheel rims are allowed. Maximum front wheel width is 8.5mm. Maximum rear wheel width is 11mm. Maximum wheel diameter is 20mm. All wheel rims must be original design made for Mini-Z RACER, any modification is not allowed, any slot-car design wheel and 3D print wheel not allowed.

Tire: Any Brand of Rubber Mini-Z production tire ONLY. Homemade tires, Foam tires, Silicon tires, Urethane tires, Ethyl Carbamate tires NOT allowed. No tire insert use. Traction compounds NOT allowed on tire or on race surface. Tire installed to wheel maximum diameter 25.5mm. Tire warmers are allowed. Tires may be cleaned with a 70% alcohol solution. If a driver uses tire cleaner that has been deemed illegal, the driver will be subject to any penalties that apply.

Minimum Weight: Whole car with everything 160g.

Formula One

Chassis: PNR 3.0F1, GL Racing GLF, G-Force Formula, MWX FormulaR1, Atomic MRZ F1 and Reflex FX28.

Body: PN F1 Body #600821 and #600822, GL F1 Body #GLF-S-001and G-Force Formula Body, #ZP06 ZPerformance F1 Body Set Grivi-Garage Karoserie Type 1 & 2 body to Formula 1 class Lexan body minimum thickness production material 0.5mm. Front Wing and Rear Wing MUST original from the chassis kit. Front bumper ball bearing NOT allowed.

Motor: Handout motor PN Brushless Sensored V4 Anima 2500kv #174425, all motor comes with standard 14.5 rotor.

Fixed Gear ratio 64 Pitch 12 Pinion (#416412WC Green, #426412WC Green, #MR2712WC Green) / 53T Spur Gear (#MR2953WC Yellow, #MR2055-T53WC Yellow, #RX2853WC Yellow, MWX Slipper Diff 53T Yellow, Xbility One 53T Yellow ONLY.

ESC: OPEN any Sensored or Sensorless ESC. Gyro and Receiver build in Gyro is not allowed.

Battery: 2S Li-Po battery. Maximum voltage 8.40 volts. Additional battery for transponder allowed.

Option Parts: Allowed any aftermarket brand production parts for PNR 3.0F1 or GLF or G-Force Formula. Allowed Z-Performance front bumper (not installed ball bearing) and rear wing. Allowed Chief Custom Front Wing CC-001 and CC002 NOT Allowed any homemade parts, 3D print option parts and prototype parts.

Wheel: PN Racing MR2088 (Black) and #MR2089 (Yellow) Machine Cut Delrin Formula Wheel ONLY. Front Wheel: #MR2088R0 (Black) #MR2089R0 (Yellow) Mini-Z 2WD Machine Cut Delrin Formula 11x20mm Flanged Wheel. #MR2088R0-19 Mini-Z 2WD Machine Cut Delrin Formula 11x19mm Flanged Wheel. Rear Wheel: #MR2088R14 (Black) #MR2089R14 (Yellow) Mini-Z 2WD Machine Cut Delrin Formula 14x20mm Flanged Wheel R14. #MR2088R14-19 (Black) #MR2089R14 (Yellow) Mini-Z 2WD Machine Cut Delrin Formula 14x19mm Flanged Wheel R14.

Tire: Any Brand of Rubber Mini-Z production tire ONLY. Homemade tires, Foam tires, Silicon tires, Urethane tires, Ethyl Carbamate tires NOT allowed. No tire insert use. Traction compounds NOT allowed on tire or on race surface. Tire installed to wheel maximum diameter 25.5mm. Tire warmers are allowed. Tires may be cleaned with a 70% alcohol solution.

Minimum Weight: Whole car with everything 140g

GTLM Super Stock (2500kv Lipo)

Chassis: Kyosho Mini-Z Racer MR01, MR015, MR02, MR03, MR04, Jomurema, GL Racing GLR, GLR-GT GLGTR, MRC MR01, PNR2.5W, PNR3.0, RTRC RTA, Atomic MRZ MRZ Pro MRX, MRX Master Edition, NEXX Specter, Reflex RX28, G-Force Lightning, MWX R.1, Xbility One, Atomic MRV and Team Associated RC28R Body 90mm-98mm wheel base only. LM Body 102mm wheel base only.

Body: Kyosho Mini-Z, TRP Scale and Jomurema GT01, GL 488 Lambo R8 911, Silver Horse Audi-R8 Sauber body and PN Racing Concept C9 ABS Body only, Z-Performance ZP08-V1 ZP08-V2 Wing allowed. full windshield and window must be installed, except for clearance, Lexan Window and Lexan Roof with original shape design allowed. Minimum weight limit 24g. The rear bumper may be removed up to Maximum 20mm from the ground.

Motor: Any 2500kv Motor Must Not Exceed 2860kv. PN Brushless Sensored V4 Anima 2500kv #174425, all motor comes with standard 14.5 rotor, and all motor will inspect by motor checker machine, make sure all motor running on same performance, and all motor will be sealed with security label, if the label removed or broken will be VOID. The motor will be provided on the first practice day entry fee included one, and each class allows to purchase an extra one motor.

Fixed Gear ratio 64 Pitch 14 Pinion (#416414WC Red or #426414WC Red or MR2714WC Brown) / 53T Spur Gear (#MR2953WC Yellow or #MR2055-T53WC Yellow or #RX2853WC Yellow, Xbility One 53T Yellow ONLY. MWX Slipper Diff Yellow Spur Gear 64P 53T ESC: OPEN any Sensored or Sensorless ESC. Gyro and Receiver build in Gyro is not allowed.

Battery: 2S Li-Po battery. Maximum voltage 8.40 volts. Additional battery for transponder allowed.

Option Parts: Any aftermarket brand Mini-Z production parts allowed, any homemade parts, 3D print option parts and prototype parts not allowed. Allowed 3D Print Transponder Holder, Body Side Clips, ESC Top Cover and front bumper allowed.

Wheel: All brand Plastic and Aluminum Mini-Z production wheel rims are allowed. Maximum front wheel width is 8.5mm. Maximum rear wheel width is 11mm. Maximum wheel diameter is 20mm. All wheel rims must be original design made for Mini-Z RACER, any modification is not allowed, any slot-car design wheel and 3D print wheel not allowed.

Tire: Any Brand of Rubber Mini-Z production tire ONLY. Homemade tires, Foam tires, Silicon tires, Urethane tires, Ethyl Carbamate tires NOT allowed. No tire insert use. Traction compounds NOT allowed on tire or on race surface. Tire installed to wheel maximum diameter 25.5mm. Tire warmers are allowed. Tires may be cleaned with a 70% alcohol solution. I

Minimum Weight: Whole car with everything 160g.

2wd Open

Chassis: Open any RWD chassis ONLY, 94mm-98mm Wheel Base ONLY.

Approved Lexan Body: PN - Supra A90, JGT1, JSK, AD4, GT4LB, 992GT3, M4GT3, Concept C9, V2 JGT01, ZLB. SBRC - Zenvo ST1, Phenom GT, NSX GT3, 458, SBX, STR, HYR, XBOW2, JX. Marka - RK-410, RK-408, RK-S, RK-PZR, RK-P-One, RK-W, RK-12, RK-TWR, RK-BLD, RK-NTI, RKHC, RK-MK4, RK-SP6, 4C, RK-MK5. Atomic - M4Z, DBX, HYP, VST. GL Racing - P1M. Protoform - P63, Venturi GT. Rad Body - Mako, Mako X and Catfish. RTRC - #XVR GTB-98LEX-0.5 XVR-GTB Lexan 98mm Body. Bittydesign - BDMZ-AS1 Ares-1, BDMZ-CA45, BDMZ-ETR Eptron XVR - Stability 98mm Body Sigma RC – SR98_PNWC Body Hobby Therapy - HT98 Body Xbility - Nova GT body SuperRad - #SR-04-28 SuperKura Lexan body minimum thickness production material 0.5mm. And minimum weight 10grams Maximum wing 45mm from the ground. The rear bumper may be removed up to Maximum 20mm from the ground. PN #600630 Carbon Wing and #600640 Lexan Wing allowed. All carbon front bumpers must have a 2mm gap or cushion at the leading edge of the carbon bumper.

Motor: Open any Mini-Z size motor 130 Brushed or 1525 1626 Brushless, Sensored or Sensorless.

ESC: Open any ESC Sensored or Sensorless. Gyro and Receiver build in Gyro is not allowed.

Battery: 2S Li-Po battery. Maximum voltage 8.40 volts. Additional battery for transponder allowed.

Option Parts: Open any parts allowed (including homemade parts, 3D print parts and prototype parts).

Wheel: All brand Plastic and Aluminum rims are allowed. Maximum front wheel width is 11mm. Maximum rear wheel width is 14mm. Maximum wheel diameter is 21mm. All wheel rims must be original design made for Mini-Z RACER, any modification is not allowed, any slot-car design wheel, 3D print wheel and Wheel Cover NOT allowed. Tire: Any Brand of Rubber Mini-Z production tire ONLY. Homemade tires, Foam tires, Silicon tires, Urethane tires, Ethyl Carbamate tires NOT allowed. No tire insert use. Traction compounds NOT allowed on tire or on race surface. Tire warmers are allowed. Tires may be cleaned with a 70% alcohol solution.

Minimum Weight: No minimum weight limit.

AWD Open

Chassis: Open any AWD chassis blet drive or shaft drive ONLY, 94mm-98mm Wheel Base ONLY.

Approved Lexan Body: PN - Supra A90, JGT1, JSK, AD4, GT4LB, 992GT3, M4GT3, Concept C9, V2 JGT01, ZLB. SBRC - Zenvo ST1, Phenom GT, NSX GT3, 458, SBX, STR, HYR, XBOW2, JX. Marka - RK-410, RK-408, RK-S, RK-PZR, RK-P-One, RK-W, RK-12, RK-TWR, RK-BLD, RK-NTI, RKHC, RK-MK4, RK-SP6, 4C, RK-MK5. Atomic - M4Z, DBX, HYP, VST. GL Racing - P1M. Protoform - P63, Venturi GT. Rad Body - Mako, Mako X and Catfish. RTRC - #XVR GTB-98LEX-0.5 XVR-GTB Lexan 98mm Body. Bittydesign - BDMZ-AS1 Ares-1, BDMZ-CA45, BDMZ-ETR Eptron XVR - Stability 98mm Body Sigma RC – SR98_PNWC Body Hobby Therapy - HT98 Body Xbility - Nova GT body SuperRad - #SR-04-28 SuperKura Lexan body minimum thickness production material 0.5mm. And minimum weight 10grams Maximum wing 45mm from the ground. The rear bumper may be removed up to Maximum 20mm from the ground. PN #600630 Carbon Wing and #600640 Lexan Wing allowed. All carbon front bumpers must have a 2mm gap or cushion at the leading edge of the carbon bumper.

Motor: Open any Mini-Z size motor 130 Brushed or 1525 1626 Brushless, Sensored or Sensorless.

ESC: Open any ESC Sensored or Sensorless. Gyro and Receiver build in Gyro is not allowed.

Battery: 2S Li-Po battery. Maximum voltage 8.40 volts. Additional battery for transponder allowed.

Option Parts: Open any parts allowed (including homemade parts, 3D print parts and prototype parts).

Wheel: All brand Plastic and Aluminum rims are allowed. Maximum Front wheel width is 11mm. Maximum Rear wheel width is 14mm. Maximum wheel diameter is 20.5mm. All wheel rims must be original design made for Mini-Z RACER, any modification is not allowed, any slot-car design wheel, 3D print wheel and Wheel Cover not allowed. Tire: Any Brand of Rubber Mini-Z production tire ONLY. Homemade tires, Foam tires, Silicon tires, Urethane tires, Ethyl Carbamate tires NOT allowed. No tire insert use. Traction compounds NOT allowed on tire or on race surface. Tire warmers are allowed. Tires may be cleaned with a 70% alcohol solution.

Minimum Weight: No minimum weight limit.

Pan Car Open

Chassis: Open any RWD chassis ONLY, 94mm-98mm Wheel Base ONLY.

Body: MUST be use the following bodies list, allow to cut the rear panel. #600800 PN Racing Lexan Pan Car Body. #600810 PN Racing BMR Lexan Pan Car Body. #600810L PN Racing BMR Lexan Light Weight Version Pan Car Body. #600819 PN Racing AMR Lexan Pan Car Body. #600819L PN Racing AMR Lexan Light Weight Version Pan Car Body. #600823 PN Racing XYC Lexan Pan Car Body #MRK-8030 Marka RK-AMR. #MRK-8031 Marka RK-LP1 Pan Car Body #AMZ-OP011 Atomic MP1. #SBRC-B011 SBRC Pan Body (Rear Wing must be not higher than the side panel). #RAD006 Rad Body Skillet. #GK00001 GKBODY LMX Pan Car Body Lexan body minimum thickness production material 0.5mm. Maximum wing 45mm from the ground. Additional wings or diffuser NOT allowed. All carbon front bumpers must have a 2mm gap or cushion at the leading edge of the carbon bumper.

Motor: Open any Mini-Z size motor 130 Brushed or 1626 Brushless, Sensored or Sensorless.

ESC: Open any ESC Sensored or Sensorless. Gyro and Receiver build in Gyro is not allowed.

Battery: 2S Li-Po battery. Maximum voltage 8.40 volts Additional battery for transponder allowed. Option Parts: Open any parts allowed (including homemade parts, 3D print parts and prototype parts).

Wheel: All brand Plastic and Aluminum rims are allowed. Maximum Front wheel width is 11mm. Maximum Rear wheel width is 14mm. Maximum wheel diameter is 20mm. All wheel rims must be original design made for Mini-Z RACER, any modification is not allowed, any slot-car design wheel, 3D print wheel and Wheel Cover not allowed.

Tire: Any Brand of Rubber Mini-Z production tire ONLY. Homemade tires, Foam tires, Silicon tires, Urethane tires, Ethyl Carbamate tires NOT allowed. No tire insert use. Traction compounds NOT allowed on tire or on race surface. Tire warmers are allowed. Tires may be cleaned with a 70% alcohol solution.

Minimum Weight: No minimum weight limit.